產品中心

SGB11-R coil core H class non-encapsulated coil dry type power transformer

The composite cross-section wound core H-class non- encapsulated creatively reformed the magnetic circuit structure of the traditional transformer and the overall layo...

我要詢價

產品概述
型號及特點
技術參數
外形尺寸

產品概述

The composite cross-section wound core H-class non- encapsulated creatively reformed the magnetic circuit structure of the traditional transformer and the overall layout of the transformer, making the product reach the international advanced level in various technologies . At the same time, it has significant advantages in energy saving and environmental protection. This product has three-phase no-load current balance, lower no-load loss and no-load current, which are 40% and 80% lower than the national standard respectively . It has smaller size and weight and lower noise. It is increasingly favored by users. Products are widely used in high-rise buildings, shopping malls , airports, subways, stations, docks, petroleum, chemical industry, nuclear power plants, nuclear submarines, densely populated areas, light rail, power plants and other places that require fire protection and explosion protection.

型號及特點

Normal usage conditions

Maximum temperature: +40℃
Maximum daily temperature: +30℃
Maximum annual average temperature: +20℃
Cooling method: AN
Minimum temperature: -30℃
Altitude:Indoor use below 1000m: (Add outer shell for outdoor use)

Performance specifications

Rated voltage: High voltage: 6.0, 10, 10.5,
11KV Low voltage: 0.4KV
High voltage tap range: +5% or 2x2.5%
Connection method: Yyn0/Dyn11
Insulation grade: H class
Insulation level: LI60AC35/AC3
sound level: 40 - 50dB

product standards

GB/T 10228-2015 Technical Parameters and Requirements for Dry-type Power Transformers"
GB 1094.11-2007 "Power Transformers Part 11: Dry-type Transformers"
GB 1094.3-2017 "Insulation Level Insulation Test and External Insulation Air Gap"
GB/T 1094.12- 2013 "Load Guidelines for Dry-Type Power Transformers"
GB 4208-2017 "IP code for enclosure protection level"
JB/T 10088-2016 "Sound level of 6~220KV transformer"

Product structure

Compared with traditional stacked iron cores, whether the iron core is stacked with direct ground seams or diagonal seams, there must be seams. The seams of the silicon steel sheets form air gaps in the magnetic circuit, so the seams are There is a magnetic flux saturation zone with high magnetic resistance, where energy loss is concentrated. If there are no seams in the core, there will be no high energy consumption areas, and the high magnetic permeability characteristics of high-quality core materials can be fully utilized.
Power transformers use wound iron cores, and their continuous winding without seams can greatly improve the magnetic circuit properties of the transformer.
The U.S. DuPont NOMEX insulation material winding technology is used in the coil insulation structure, which improves the products insulation heat resistance to H level and reduces combustibles by 80%.
The low voltage coil adopts foil coil construction.
The high-voltage coil adopts a cake-type coil structure. Since it is wound with NOMEX paper-wrapped copper wire, the space between the cakes is fully supported by polymer composite gaskets.
The foil-type low-voltage coil and the pie-type high-voltage coil cooperate with each other, and the leakage reactance at the end of the winding is small, which improves the short-circuit resistance of the transformer.
The high and low voltage coils are made of NOMEX insulation material and polymer composite materials, which can maintain high electrical performance regardless of humid conditions or high temperature conditions.

Features

The three-phase current is basically balanced, which reduces the active power loss caused by the unbalanced three-phase current of the power grid during operation.
The iron core has no seams, and through annealing treatment, the no-load loss and no-load current are significantly reduced compared to the laminated iron core. They are reduced by 30-40% and 80% respectively compared with the same period of SCB9, achieving the purpose of energy saving and consumption reduction.
The iron core is seamless, and the noise of the transformer is greatly reduced, 10dB lower than the traditional one, and the noise is below 50dB.
The high-voltage coil adopts a pie coil structure, wound by DuPont paper-wrapped copper wire, and supported by high-frequency composite materials to minimize partial discharge.
The foil-type low-voltage coil and the pie-type high-voltage coil are the best combination. The leakage reactance at the end of the winding is small. At the same time, the coil support and compression device is evenly distributed, so the transformer has strong short-circuit resistance.
The materials used in this product are heat-resistant and flame-retardant, especially insulation materials, which have been used in the aviation industry. This product has good high temperature resistance and fire resistance, and will not release toxic or corrosive substances even at high temperatures of 800°C.
The unique craftsmanship of the composite coil core, the perfect combination of technology and tradition, is developed based on the experience of successful operation of traditional transformers, which improves the ventilation effect of the transformer itself and achieves better heat dissipation. Therefore, the service life of the product is extended, the overload capacity is improved accordingly, and it can operate safely for a long time under 120% overload condition.

技術參數

SGB11-R Technical specifications

額定容量 (KVA) Rated capacity	SC9		SGB11-R		SGB11-R比SC9下降(%) Compared with SC9, SGB11-R products declines by
額定容量 (KVA) Rated capacity	空載電流(%) No-Load current	空載損耗(W) No-Load loss	空載電流(%) No-Load current	空載損耗(W) No-Load loss	空載電流(%) No-Load current	空載損耗(W) No-Load loss	噪聲(%) Noise
50	2.1	320	0.5	230	76.1	39	30
80	2.1	400	0.5	300	76.1	33.3
100	1.8	430	0.4	330	77.7	30.1
125	1.6	490	0.4	390	75	25.6
160	1.4	580	0.4	450	71.4	29
200	1.4	650	0.3	500	78.5	30
250	1.4	780	0.3	600	78.5	30
315	1.4	920	0.3	700	78.5	31.5	30
400	1.2	1050	0.3	780	75	34.6
500	1.2	1200	0.3	920	75	30.5
630	1.2	1500	0.3	1010	75	48.5
630	1	1400	0.3	1050	70	33.3
800	1	1650	0.2	1270	80	30
1000	0.8	1950	0.2	1485	75	31.3
1250	0.8	2250	0.2	1785	75	26.1
1600	0.8	2650	0.2	2050	75	29.2
2000	0.6	3600	0.2	2490	66	44.5
2500	0.6	4350	0.2	3000	66	45

SGB11-R-50~2500/10 coil core dry type transformer technical parameters

額定容量 (KVA) Rated capacity	空載損耗(W) No-Load loss		負載損耗W(145°C) Load loss		空載電流(%) No-Load current		聲級(LPA)db Sound level(LPA) db		阻抗電壓 (%) Impedance voltage
額定容量 (KVA) Rated capacity	國標 National standard	企標 En terprise standard	國標 National standard	企標 Enterprise standard	國標 National standard	企標 Enterprise standard	國標 National standard	企標 Enterprise standard	阻抗電壓 (%) Impedance voltage
50	360	230	1490	1040	2.8	0.5	55	45	4
80	460	300	2150	1500	2.6	0.5	55	45	4
100	510	330	2550	1530	2.4	0.4	55	45	4
125	600	390	3050	1830	2.2	0.4	56	45	4
160	700	450	3650	2190	2.2	0.4	58	45	4
200	820	500	4680	2808	2.0	0.3	58	45	4
250	950	600	5500	3300	2.0	0.3	58	46	4
315	1100	700	6600	3960	1.8	0.3	60	46	4
400	1300	780	7800	4680	1.8	0.3	60	46	4
500	1500	920	9350	5610	1.8	0.3	62	46	4
630	1750	1010	10900	6540	1.6	0.3	62	48	4
630	1680	1050	11500	6900	1.6	0.3	62	48	6
800	2120	1270	13600	8160	1.6	0.2	64	48	6
1000	2480	1485	15700	9420	1.4	0.2	64	49	6
1250	2980	1785	18400	11040	1.4	0.2	65	49	6
1600	3420	2050	21300	12780	1.4	0.2	66	49	6
2000	4150	2490	25000	15000	1.2	0.2	66	50	6
2500	5000	3000	29100	17460	1.2	0.2	67	50	6

外形尺寸

型號 Type	非封閉式(無防護外罩) No-encapsulated (without protective housing) LxBxH	m	n	g	封閉式(有防護外罩) Encapsulated (with protective housing) LxBxH	M	重量 kg Weight
SG11-50/10	1120x700x1050	330	600	700	1420x1230x1330	330	600
SG11-80/10	1120x700x1050	330	600	700	1420x1230x1330	330	630
SG11-100/10	1120x700x1050	400	600	700	1420x1230x1330	400	660
SG11-125/10	1130x700x1135	400	600	700	1430x1250x1390	400	720
SG11-160/10	1150x700x1145	550	600	700	1450x1260x1400	550	830
SG11-200/10	1170x800x1160	550	700	700	1470x1260x1410	550	920
SG11-250/10	1195x800x1220	590	700	700	1500x1280x1470	590	1020
SG11-315/10	1220x800x1260	550	700	700	1520x1290x1510	550	1170
SG11-400/10	1260x900x1350	550	800	1000	1560x1310x1600	550	1480
SG11-500/10	1295x900x1455	550	800	1000	1600x1320x1710	550	1690
SG11-630/10	1451x1000x1340	660	900	1000	1720x1440x1590	660	1840
SG11-630/10	1415x1000x1340	660	900	1000	1720x1440x1590	660	1840
SG11-800/10	1475x1000x1355	780	900	1000	1780x1540x1610	780	2100
SG11-1000/10	1525x1000x1490	830	900	1000	1830x1560x1740	830	2380
SG11-1250/10	1580x1100x1510	665	1000	1000	1880x1580x1760	665	2830
SG11-1600/10	1660x1250x1570	665	1150	1000	1960x1600x1820	665	3700
SG11-2000/10	1730x1250x1715	660	1150	1000	2130x1630x1970	660	4310
SG11-2500/10	1825x1250x1760	680	1150	1000	2130x1640x2010	660	4810

Note: If there is any change in the above dimensions, the actual product shall prevail.

上一篇：

下一篇：

^{<blockquote id="dw1m5"></blockquote>}

產品中心

SGB11-R coil core H class non-encapsulated coil dry type power transformer

在線詢價

產品中心

快速導航

掃描二維碼

官方微信公眾號

添加微信好友